Language:
[简体中文]

 0086-18055211309

 info@siliconeoil.net

Products

News

Contact Us

    Office     Address:Sunmoon Science Park, 985 Xingzhong Road, High-Tech Zone, Bengbu, China
    Factory   Address:Mohekou Industrial Park, Huaishang District, Bengbu, Anhui, China
    Contact:Amina Zhang
    Phone:0086-18055211309
    FAX:0086-552-3822922
    Mobile:+86 18055211309
    WebSite:www.iotachem.com
    www.siliconeoil.net
    Email:info@siliconeoil.net
    QQ:


  • Switching to a Waterborne Silicone Release Agent for PET: What Should You Check?

    Switching Waterborne Silicone Release Coatings for PET Film

    Solids content helps estimate how much liquid you will handle and how much dry matter might remain. It does not show whether an emulsion will coat your PET evenly, cure in the existing oven or transfer to the back of the film after winding. When requesting a quote, start with the film, the coating line and the adhesive used in lamination.

    Line conditions to share with suppliers

    If line speed and oven length are fixed, tell the supplier how long the film actually spends in the oven. The oven setpoint alone does not tell you the temperature the film surface reaches. Even when two emulsions have the same nominal solids, check each supplier's application conditions.

    What to share when requesting a quote

    What to check in the coating trial

    PET grade, thickness, coating side and surface treatment

    Check uniformity, dewetting, bare spots and whether the cured coating rubs off.

    Coater, line speed, oven and any measured film surface temperatures

    Check whether the existing line can produce a stable coating and log any adjustments.

    Actual adhesive, peel speed and acceptance limits

    Compare release force under the same conditions and check how well the adhesive bonds after peeling.

    Winding conditions, storage time and delivery format

    Look for blocking or possible transfer on unwinding and recheck the agreed limits after storage.


    IOTA 2121E silicone release emulsion for PET coating

    The product page lists IOTA 2121E as a release emulsion for substrates including PET film and gives a solids content of 40%. That figure helps identify the grade as supplied. Verify the film surface, coating equipment and cure conditions on your line before setting a mix ratio or line speed.

    Cost per usable square metre after a successful trial

    Use PET from the same batch and the same adhesive, with the current coating as a control. If the new coating requires a lower line speed or a higher dry coat weight, or results in more rejected rolls, the price per kilogram can understate the cost of switching. Record actual consumption, usable area and line speed. The solids in the product as supplied are not necessarily the amount of effective silicone deposited on the film.

    Keep sample evaluation and purchasing separate. Trial records show how the material runs on the line; purchase documents specify product identity, supply specifications, batch documentation and change notification. IOTA Silicone Oil (Anhui) Co., Ltd. provides solutions across the silicone value chain. We can help check candidate materials and product data against your substrate and line conditions. We do not provide complete formulations or formulation development services.

    Frequently asked questions

    Q1 Can I switch directly if both emulsions are 40% solids?

    Check how solids content is defined and the form in which each product is supplied. Then verify wetting, cure, coating adhesion and performance with the actual adhesive.

    Q2 Is meeting the release force spec enough for approval?

    Also check the adhesive's bond after peeling and the roll's performance after winding and storage, against project requirements.

    Q3 Can a small coupon replace a full roll trial?

    A coupon can screen candidates. For roll production, verify continuous coating, oven conditions and winding.

    Q4 Is the oven setpoint enough?

    Also send the line speed, effective oven length and any available film surface temperature data to establish the actual heat exposure.

    Q5 Does a product listed for PET automatically suit my project?

    It is a candidate. Confirm the combination of film surface, equipment and adhesive in a line trial.

    Related product

    IOTA 2121E silicone release emulsion



Feedback to "Iota Silicone Oil (Anhui) Co., Ltd."

  • *Name:
    *Contacts:
    *Content:
    *Code:    验证码

    Iota Silicone Oil welcome your message...

New Products

皖ICP备14007495号

Copyright © 2000-2026 Iota Silicone Oil (Anhui) Co., Ltd, All Rights Reserved