Verifying tank mix compatibility crop safety and application performance with IOTA 2000-IOTA

Products

News

Office Address:	Sunmoon Science Park, 985 Xingzhong Road, High-Tech Zone, Bengbu, China
Factory Address:	Mohekou Industrial Park, Huaishang District, Bengbu, Anhui, China
Contact:	Amina Zhang
Phone:	0086-18055211309
FAX:	0086-552-3822922
Mobile:	+86 18055211309
WebSite:	www.iotachem.com www.siliconeoil.net
Email:	info@siliconeoil.net
QQ:

News > Dynamic industry > Verifying tank mix compatibility crop safety and application performance with IOTA 2000

Verifying tank mix compatibility crop safety and application performance with IOTA 2000

After IOTA 2000 is added to a tank mix, the absence of separation and faster spreading on leaves still do not remove the need to check spray coverage, crop response and actual application performance separately. A stable appearance in a beaker supports only a preliminary assessment of physical compatibility. It is not sufficient grounds for scaling up in the field.

If excessive spreading and runoff are already occurring, first check concentration, spray volume and equipment using the existing approach. This article covers the subsequent acceptance checks for R&D, purchasing and application teams preparing small scale trials. It gives no unverified dosage intended for all crops.

Confirm the product and the permitted conditions of use

Start with the public information on IOTA 2000 agricultural silicone surfactant, then decide whether to run a trial based on the actual pesticide label, target crop and application method. Polyether modified agricultural silicone surfactants may be considered as candidate tank mix adjuvants. [1]

IOTA Silicone Oil (Anhui) Co., Ltd. provides solutions across the silicone value chain.

First check the pesticide label for permitted adjuvant types, rates and mixing restrictions. Combinations not permitted by the label must not proceed to larger trials. If the requirements are unclear, consult the registration holder or local crop protection specialists first. Extension information from abroad is a technical reference; it does not replace label and regulatory requirements in China or the target market. [2]

Record four types of results separately

What to verify	What to observe or measure	What this does not establish
Physical tank mix compatibility	Flocculation, floating oil, sediment, foam and passage through filters	Absence of crop injury or stability of active ingredients
Spray coverage	Distribution at target locations, missed areas and runoff	Increased uptake or better pest control
Crop safety	Leaf spots, scorch, curling, growth changes and abnormalities in sensitive organs	Safety on other cultivars or at other growth stages
Application performance	Assessment against the target pest, disease or weed and trial protocol	Permission to reduce the labelled pesticide rate independently

If chemical stability of the active ingredient must be demonstrated, arrange suitable analysis separately. A clear, unseparated appearance cannot replace it. Coverage can be checked with an appropriate tracer or sampling method. Spots on water sensitive paper alone do not establish uptake by actual leaves.

Design the comparison around one specific question

For example, to ask whether a candidate adjuvant warrants further evaluation under the current spray conditions, first hold the pesticide, water, nozzle, pressure and spray volume per unit area constant. Use sufficient replicates for each treatment and randomize their positions to reduce misleading effects from plot and plant differences. The trial lead must set the number of replicates and assessment times in advance.

1. Include an untreated control to identify pre-existing lesions, environmental injury and natural growth changes.

2. Include the same pesticide without the additional candidate adjuvant to compare the effect of adding it. If the label requires a particular type of adjuvant, the trial lead must design the control within permitted conditions rather than deliberately breaching the label.

3. Test candidate combinations within the limits of the label and product information. Record every ingredient and the actual rates. If the adjuvant’s own effect must be isolated, have a specialist design the relevant additional controls.

4. Under the same assessment conditions, record coverage, crop response and application performance separately. Do not base the conclusion on a single photograph selected for the greatest spreading.

Observe crop safety under the intended conditions of use

University extension information notes that crop response to silicone surfactants depends on the pesticides used with them, the rate and the environment. It also documents injury to ornamental plants under hot, sunny conditions. [2]

Use the target cultivar and growth stage in the small scale trial, retaining photographs and markers from before treatment. Continue observations at the predefined times; the absence of abnormalities on the application day is not the endpoint. If abnormalities occur, pause scale-up and review the pesticide, adjuvant, other tank mix components, weather and pre-existing plant condition. Do not immediately attribute the problem to one ingredient.

Hand over the trial conditions before scaling up

Record	Minimum information
Crop	Cultivar, growth stage, leaf condition and pre-existing abnormalities
Tank mix	Pesticide formulation, other adjuvants, water source, actual rates and preparation time
Equipment	Nozzle, pressure, measured flow, travel speed and spray volume
Environment	Temperature, humidity, wind and weather before and after application
Results	Coverage, crop response, application performance and photograph IDs for all comparison groups

After a change of crop, pesticide, water source or application equipment, reassess whether the existing conclusions still apply. For purchasing acceptance, also retain the product batch number, applicable TDS version and batch COA. Without trial results, do not describe a case as demonstrating improved efficacy or crop safety.

Frequently asked questions

Q1 Can a mix go to the field if it does not separate in a cup

The label conditions, spray behavior and target crop response still need checking. A cup test mainly screens for visible physical mixing problems.

Q2 Does a larger spreading area prove better efficacy

Spreading reflects only part of the interfacial behavior. Application performance must be evaluated independently against the target pest, disease or weed and the trial protocol.

Q3 Does safety on one crop establish safety on others

No direct extrapolation is justified. Reassess suitability when the cultivar, growth stage, pesticide combination or environment changes.

Q4 Is the absence of leaf spots enough to establish safety

Also check sensitive organs, growth and other responses required by the project throughout the specified observation period, rather than only on application day.

Q5 Can the pesticide rate be reduced after adding IOTA 2000

Adding it does not justify independently reducing the labelled rate. Any adjustment must comply with the applicable label, local requirements and relevant validation.

Q6 What trial information should be sent to IOTA

Provide the crop and growth stage, complete tank mix composition, water, equipment settings, weather and results for every comparison group. These support discussion of the material and conditions for the next validation step.

*Name:

*Contacts:	Tel/Mobile: Email/Skype: Address:

*Content:
*Code:
Iota Silicone Oil welcome your message...

Home

About

News

Products

Service

Careers

Contact